First of all, the operator must be very familiar with the CNC cutting machine, whether it is the structure of the cutting machine, the scope of application, or the technical specifications of the cutting machine, as well as the safety rules that must be observed when using, they must be familiar with the heart, so as to avoid accidents when using. In addition, before the formal operation, the operator is generally required to take an examination. Only those who pass the examination can operate the CNC cutting machine.

數控開料機一旦進行操作，就非常容易發生意外，對機器以及設備操作者都造成非常---的損傷，所以必須要引起各部門的高度重視。

Once the CNC cutting machine is operated, it is very easy to have accidents, which will cause great damage to the machine and equipment operators, so it must be paid attention to by all departments.

櫥柜門板生產設備用久了也會出現這樣那樣的毛病，下面就跟小編一起來看看該如何保養櫥柜門板生產設備吧：

The cabinet door panel production equipment will also have such and such problems after long use. Let's take a look at how to maintain the cabinet door panel production equipment with Xiaobian

一、連續運行時間每天10小時以下，冷卻水的清潔及水泵的正常工作，絕不可使水主軸電機出現缺水現象，定時更換冷卻水，以防止水溫過高。冬季如果工作環境溫度太低可把水箱里面的水換成防凍液。

1、 The continuous operation time is less than 10 hours per day. The cleaning of the cooling water and the normal operation of the water pump must not make the water spindle motor short of water. The cooling water should be replaced regularly to prevent the water temperature from being too high. If the working environment temperature is too low in winter, the water in the water tank can be changed into antifreeze.

二、每次機器使用完畢，要注意清理，務必將平臺及傳動系統上的粉塵清理干凈，定期(每周)對傳動系統(x、y、z三軸)潤滑加油。(注：x、y、z三軸光桿用機油進行保養;絲桿部分加高速黃油;冬季如果工作環境全自動電腦雕刻機溫度太低絲桿、光桿(方形導軌或圓形導軌)部分應先用汽油進行沖洗清潔，然后加入機油，否則會造成機器傳動部分阻力過大而導致機器錯位。)

2、 Every time the machine is used, pay attention to cleaning, be sure to clean up the dust on the platform and transmission system, and lubricate the transmission system (x, y, z axes) regularly (weekly). (Note: the X, y, Z three-axis polished rod is maintained with engine oil; the screw rod part is added with high-speed grease; if the temperature of the fully automatic computer engraving machine is too low in winter, the screw rod and polished rod (square or circular guide rail) part should be washed with gasoline first, and then added with engine oil, otherwise the resistance of the machine transmission part will be too large and the machine will be misplaced. )

三、對電器進行保

3、 Protect electrical appliances

養檢查是，一定要切斷電源，待---無顯示及主回路電源指示燈熄滅后，電腦木工雕刻機可進行。

Maintenance inspection is, be sure to cut off the power supply, until --- no display and main circuit power indicator light off, computer woodworking engraving machine can be carried out.

四、長期不使用本機時，應把各部分擦拭干凈，并用塑料或篷布覆蓋防塵。

4、 When the machine is not used for a long time, all parts should be wiped clean and covered with plastic or tarpaulin to prevent dust.

以上就是櫥柜門板生產設備的保養方法建議希望能給大家能帶來幫助，櫥柜門板生產設備在企業生產運營中是站著非常重要的位置，一旦機器出現了故障也會延遲了生產工期，所以機器的保養和維護是非常重要的。

The above is the maintenance method of cabinet door production equipment. I hope it can help you. Cabinet door production equipment is very important in the production and operation of enterprises. Once the machine fails, it will delay the production period, so the maintenance and maintenance of the machine is very important.