1. Open the engraving programming software of stone engraving machine and program the engraving path: for example, if engraving, first arrange the version with Wentai software, and then input the parameters such as depth, overlap rate and line spacing in the pop-up dialog box through 2D, 3D and cutting, and then let the computer calculate. If processing relief, first use ArtCAM or precision carving to generate relief through files or model pictures, then determine the size, and start calculation by filling in each processing parameter. After the path is generated, colored lines will be generated on the word or model, which is often called tool path.

2、輸出雕刻路徑并輸入雕刻機控制系統軟件：在文泰、精雕、ARTCAM等軟件里輸出文件，如果是雕刻機控制系統不能支持的格式，還需要轉換。常用的程序格式有nc、mmg等。

2. Output engraving path and input engraving machine control system software: output files in Wentai, Jingdiao, ArtCAM and other software. If it is a format that cannot be supported by engraving machine control system, it needs to be converted. The commonly used program formats are NC, MMG, etc.

3、檢查機器并正確固定工件：看機器臺面上是否有雜物，尤其是石材顆粒、大面積的石粉、砂子等，要注意清理，否則容易影響材料的平面度。造成深淺不一(解決不平問題可以訪問我們的官網查看有關石材雕刻機調平系統又稱刻字寶的說明)。

3. Check the machine and fix the workpiece correctly: check whether there are sundries on the machine table, especially stone particles, large-area stone powder, sand, etc. pay attention to cleaning, otherwise it is easy to affect the flatness of the material. Cause different depth (to solve the problem of unevenness, you can visit our official website to see the instructions on the leveling system of stone carving machine, also known as engraving treasure).

將工件按排版編程軟件里的放置方向，看橫向還是豎向放置材料。注意材料和機器走向軸方向平行，不要放偏了。

Place the workpiece according to the placement direction in the typesetting programming software to see whether the material is placed horizontally or vertically. Note that the material is parallel to the axis of the machine, and do not deviate.

用壓板固定材料，一般固定方式有壓和頂兩種。如果是用壓板壓的話，注意不要壓在材料的加工部分，防止機器撞車、撞刀。

Fix the material with pressing plate. Generally, there are two fixing methods: pressing and jacking. If the pressing plate is used, be careful not to press it on the processing part of the material to prevent the machine from crashing and hitting the knife.

4、確定工件坐標系原點，也就是我們常說的對刀。分別將機器的各個軸原點對齊原點，然后數據歸零或者輸入相應坐標系坐標值。

4. Determine the origin of workpiece coordinate system, that is, we often say tool setting. Align the origin of each axis of the machine with the origin respectively, and then return the data to zero or enter the coordinate value of the corresponding coordinate system.

5、檢查噴水、水循壞，調整機器轉速和進給速度，并在石材雕刻機控制系統軟件里進行仿真，如果是維宏系統的話，按F8即可。查看仿真無誤，再按F8推出仿真。

5. Check the water spray and water circulation, adjust the machine speed and feed speed, and simulate it in the control system software of stone carving machine. If it is Weihong system, press F8. Check that the simulation is correct, and then press F8 to launch the simulation.